- Vcds Windows 10
- Vcds Interface Not Found Port Ok
- Vcds Interface Not Found 19.6.1
- Vcds Interface Not Found
- Port Status Ok Interface Not Found Vcds
- Vcds Interface Not Found Windows 10
VCDS 18.2.1 VAG-COM K+CAN HEX interface for VAG car Interface not found problem still puzzle our client for it. Below eobdtool.com share VCDS 18.2.1 Vagcom Cable VCDS 18.2.1 VAGCOM Interface not found solution solution as following.
VCDS VAG-COM 18.2.1 Problem:
I was able to register the VCDS 18.2.1 software successfully but now I can’t seem to get the port to work.
- Posted November 21, 2009. Just upgraded to 908 & I now get the following message (genuine cable, licence from Rosstech, 2 cars same laptop). When not connected to car get Port Status OK Interface Found! Type Rosstech Hex-USB Status Not plugged into car but when connect to car get the 'port status ok interface.
- Vcds windows based vag vas emulator running on windows 10 x64. Vcds version: 17.8.0.1 (x64) data version: 20170721 ds276.2. Last week i attempted to connect it again and run it via vcds (version 18.1 this had been auto updated by itself) but it barfed with an error: ross tech usb interface not found!
Every time i plug the cable into the car and try to save the port, it tell me that the interface is not found. But when the cable is not plugged into the car, the port works fine…..
Port status ok Interface not found! This is not a problem You will only get Interface found connected to the car with the ignition switched on so the dash warning lights are active. Edited to add: You can only save the settings once you have tested the interface connected to the car with the ignition on.
Vcds Windows 10
Help is appreciated ..: thank you
Eobdtool.com VCDS 18.2.1 VAGCOM VCDS Cable Solution:
Reinstalled the VCDS software and choose install 32-bit EXE on 64-bit System
Need Ross-Tech VCDS 18.2.1 VAG-COM 1:1 Original Plan VCDS HEX K+CAN Interface just contact us freely.
Eobdtool.com Kindly note: we do not offer after-sales for the product from other supplier, need anyhelp pls keep your order number from eobdtool.com ask for help. Thanks.
Focus On OBD Tool Since 2008
Follow Us:www.facebook.com/eobdtool
Skype:eobdtool02
Vcds Interface Not Found Port Ok
Wechat/WhatsApp:(+86)13728823411
Email:[email protected]
Website:www.eobdtool.com
How to solve Vag Com VCDS hardware not find recognise problem
When need diagnostic interface for vag cars, vag com vcds cables are customers first choice. While lately customers feedback they can't found the vag com hardware and recognise vag com interface when the Turial of China vag com 11.11/11.8/11.3 programming and upgrading.
OBD2repair.com VCDS VAG COM Tips:
Vcds Interface Not Found 19.6.1
We also offer original plan Work with Original VCDS Software pls check :
Vcds Interface Not Found
Port Status Ok Interface Not Found Vcds
What should we do to solve this problem?
VAG com 11.11 VCDS 11.11 vagcom 11.11
Error: Vag Com does not work , (not plugged into car message / interface not work) and can't update it to Vag com 12.10.3.
Here OBD2Repair share with you the solution
Vcds Interface Not Found Windows 10
Step 1:- Reflash Atmega with dump. Firstly, supply 12V power to the Vag com VCDS interface, Connect ATMEGA 162 chip with port LPT of the pc to program it as shown on this picture:
Step 2:- Remove components IC8 , R50 , R51 , D7 as shown on the pic with red arrows.
Step 3:- Reflash FTDI with dump.
Step 4:-- Reflash GAL16V8 (ATF16V8) with dump.
Step 5:-- Solder 3 wires as shown on the pic with blue lines.
Step 36:-- Copy loader to your VCDS directory.
Q:
When plug the vag com 11.11 with your pc, it is not recognised and comes up as 'FFFFFFFFFFFFF'.
Any advise please?,It worked fine for the first 2-3 times.
A: Reprogram it, you need Reflash the china vag com
When vag com have any question, you must program Atmega162 with an external programmer
After that you need to program FTDI over USB with Mprog
For RL cable you must program GAL/ATF - I assume that you have a RL cable because you asked loader
and for RL cable you need to do some modifications to the PCB
then install VCDS 11.11.0 and copy loader to installation folder
Make a shortcut to your desktop (loader)
every time you want to use VCDS -- click the shortcut on the desktop
Final solution for Chinese VAG COM interfaces with protection chip and FT232R
Here you have a tutorial for programming Atmega chip(vag com )
The document you need for solve vag com vcds problem free download:
Chinese RL cable repair.rar
11.11 full dump.rar
FT232RL.rar
VCDS 11.11.0 loader.rar